Toshiba Blu ray Player BDX2400KU User Manual

Media Box and Blu-ray Disc™ Player  
User’s Guide:  
BDX2400KU/BDX3400KU  
If you need assistance:  
Toshiba’s Support Web site  
support.toshiba.com  
For more information see “Troubleshooting” on page 37 in  
this guide  
Owner’s Record  
The model number and serial number are on the back and  
underside of your player. Print out this page and write these  
numbers in the spaces below. Refer to these numbers  
whenever you communicate with your Toshiba dealer about  
this equipment.  
Model name _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _  
Serial number _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _  
 
3
SAFETY PRECAUTIONS  
The rating plate and the safety caution are on the rear of the unit.  
WARNING:  
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE  
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG  
TO WIDE SLOT OF AC POWER OUTLET, THEN FULLY INSERT.  
The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to alert the user  
to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient  
magnitude to constitute a risk of electric shock to persons.  
The exclamation point within the equilateral triangle is intended to alert the user to the presence of important  
operating and maintenance (servicing) instructions in this User’s Guide.  
CAUTION: This device employs a Laser System.  
Warning:  
The main plug is used as disconnect device and it  
To ensure proper use of this product, please read this User’s  
Guide carefully and retain for future reference. Should the  
unit require maintenance, contact an authorized service  
location. Use of controls or adjustments or performance of  
procedures other than those specified herein may result in  
hazardous radiation exposure.  
To prevent direct exposure to laser beam, do not try to open  
the enclosure. Visible and invisible laser radiation when  
open and interlocks defeated.  
should be located in such a manner that it can be easily  
unplugged in case the product requires service. In order  
to disconnect the apparatus from the main completely,  
the main plug should be disconnected from the main  
socket outlet completely.  
The apparatus shall not be exposed to dripping or  
splashing and that no objects filled with liquid, such as  
vases, shall be placed on the apparatus.  
Always leave a space of at least 4 (four) inches around  
the apparatus. The slots and openings are provided  
to protect the apparatus from overheating and to help  
maintain reliable operation.  
DO NOT STARE INTO BEAM  
Keep the product away from direct sunlight, extreme  
cold, or heat sources such as a heater. This may reduce  
the life of the product.  
The symbol for Class II  
(Double lnsulation)  
Location of the required label  
Products that earn the ENERGY STAR  
prevent green house gas emissions by  
meeting strict energy efficiency guidelines  
set by the U.S. Environmental Protection  
Agency and the U.S. Department of Energy.  
ENERGY STAR and the ENERGY STAR  
mark are registered U.S. marks.  
The rating plate  
and the safety  
caution are on the  
rear of the unit.  
 
4
IMPORTANT SAFETY INSTRUCTIONS  
1. Read these instructions.  
2. Keep these instructions.  
11. Only use attachments/accessories specified by the  
manufacturer.  
3. Heed all warnings.  
4. Follow all instructions.  
12. Unplug this apparatus during lightning storms or when  
unused for long periods of time.  
5. Do not use this apparatus near water.  
6. Clean only with a dry cloth.  
7. Do not block any of the ventilation openings. Install in  
accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as radiators,  
heat registers, stoves, or other apparatus (including  
amplifiers) that produce heat.  
13. Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has been  
damaged in any way, such as the power-supply cord  
or plug is damaged, liquid has been spilled or objects  
have fallen into the apparatus, the apparatus has been  
exposed to rain or moisture, does not operate normally,  
or has been dropped.  
9. Do not defeat the safety purpose of the polarized or  
grounding-type plug. A polarized plug has two blades  
with one wider than the other. A grounding type plug  
has two blades and a third grounding prong. The wide  
blade or the third prong is provided for your safety. If  
the provided plug does not fit into your outlet, consult  
an electrician for replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or  
pinched particularly at plugs, convenience receptacles,  
and the point where they exit from the apparatus.  
ADDITIONAL SAFETY INSTRUCTIONS  
14. Do not overload wall outlets; extension cords, or 19. Do not use a cracked, deformed, or repaired disc.  
integral convenience receptacles as this can result in  
a risk of fire or electric shock.  
These discs are easily broken and may cause serious  
personal injury and apparatus malfunction.  
15. Never expose the apparatus to dripping or splashing or 20. If the apparatus should emit smoke or an unusual odor,  
place items such as vases, aquariums, any other item  
filled with liquid, or candles on top of the unit.  
16. Keep your fingers well clear of the disc tray as it is  
closing. Neglecting to do so may cause serious  
personal injury.  
immediately disconnect the power cord from the wall  
outlet. Wait until the smoke or smell stops, then ask  
your dealer for a check and repair. Neglecting to do so  
may cause fire.  
21. During thunderstorms, do not touch the connecting  
cables or the apparatus.  
17. Do not place anything on top of this unit.  
18. Never block or cover the slots or openings in the unit. 22. Warning: To prevent spread of fire, keep candles or  
Never place the unit:  
other open flames away from this product at all times.  
on a bed, sofa, rug or similar surface;  
too close to drapes, curtains, or walls; or  
in a confined space such as a bookcase, built-in cabinet,  
or any other place with poor ventilation.  
The slots and openings are provided to protect the  
unit from overheating and to help maintain reliable  
operation.  
 
5
USA  
Canada  
Industry Canada Statement  
Federal Communications Commission Statement  
FCC Compliance Statement  
This device complies with RSS-210.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and  
(2) This device must accept any interference received,  
including interference that may cause undesired operation  
of the device.  
This device and its antenna(s) must not be co-located  
or operating in conjunction with any other antenna or  
transmitter.  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions: (1)  
This device may not cause harmful interference, and (2)  
This device must accept any interference received, including  
interference that may cause undesired operation  
Interference  
This equipment has been tested and found to comply with  
the limits for a Class B digital device, pursuant to Part 15  
of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses,  
and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause  
harmful interference to radio communications. However,  
there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one of the  
following measures:  
Wireless Radio  
For product available in the USA/Canada market, only  
channel 1-11 can be operated. Selection of other channels  
is not possible. The device could automatically discontinue  
transmission in case of absence of information to transmit,  
or operational failure. Note that this is not intended to  
prohibit transmission of control or signaling information  
or the use of repetitive codes where required by the  
technology.  
Important: Any changes or modifications not expressly  
approved by the party responsible for compliance could  
void the user’s authority to operate this equipment.  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and  
receiver.  
IMPORTANT NOTE:  
IC Radiation Exposure Statement: This equipment complies  
with IC RSS-102 radiation exposure limits set forth for  
an uncontrolled environment. This equipment should  
be installed and operated with minimum distance 20cm  
between the radiator & your body.  
Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician  
for help.  
Wireless Radio  
For product available in the USA/Canada market, only  
channel 1-11 can be operated. Selection of other channels  
is not possible. The device could automatically discontinue  
transmission in case of absence of information to transmit,  
or operational failure. Note that this is not intended to  
prohibit transmission of control or signaling information  
or the use of repetitive codes where required by the  
technology. If this device is going to be operated in 5.15-  
5.25GHz frequency range, then it is restricted to an indoor  
environment only.  
Important: Any changes or modifications not expressly  
approved by the party responsible for compliance could void  
the user’s authority to operate this equipment. This device  
and its antenna(s) must not be co-located or operating in  
conjunction with any other antenna or transmitter.  
FCC Radiation Exposure Statement  
This equipment complies with FCC radiation exposure limits  
set forth for an uncontrolled environment. This equipment  
should be installed and operated with minimum distance  
20cm between the radiator & your body  
 
6
PRECAUTIONS  
Notes on handling  
Notes on moisture condensation  
Moisture condensation damages the Symbio™ Media  
Box and Blu-ray Disc™ Player. Please read the following  
carefully:  
When shipping the unit, the original shipping carton  
and packing materials come in handy. For maximum  
protection, repack the unit as it was originally packed at  
the factory. Take care not to give it a shock or shake when  
carrying.  
Do not use volatile liquids, such as insect spray, near the  
unit. Do not leave rubber or plastic products in contact  
with this unit for a long time. They will leave marks on the  
finish.  
Moisture condensation occurs, for example, when you  
pour a cold drink into a glass on a warm day.  
Drops of water form on the outside of the glass.  
In the same way, moisture may condense on the optical  
pick-up lens inside this unit, one of the most crucial  
internal parts of the unit.  
The top and rear panels of the unit may become warm  
after a long period of use. This is not a malfunction.  
When the unit is not in use, be sure to remove the disc  
and turn off the power.  
If you do not use the unit for a long period, the unit may  
not function properly in the future. Turn on and use the  
unit occasionally.  
Moisture condensation occurs during the following  
cases.  
When you bring the unit directly from a cold place to a  
warm place.  
When you use the unit in a room where you just turned  
on the heater, or a place where the cold wind from the air  
conditioner directly hits the unit.  
Notes on locating  
In summer, when you use the player in a hot and humid  
place just after you move the unit from an air conditioned  
room.  
Place the unit on a level surface. Do not use it on a shaky  
or unstable surface such as a wobbling table or inclined  
stand. The loaded disc may come off the proper position  
and cause damage to the unit.  
When you use the player in a humid place.  
When you place this unit near a TV, radio, or VCR, the  
playback picture may become poor and the sound may  
be distorted. In this case, place the unit away from the TV,  
radio, or VCR.  
Do not use this unit in places which are extremely hot, cold,  
dusty or humid.  
Do not restrict the air flow of this unit by placing it  
somewhere with poor air flow, by covering it with a cloth,  
or by placing it on bedding or carpeting.  
Do not use the Symbio™ Media Box and Blu-ray  
Disc™ Player when moisture condensation may  
occur.  
If you use the unit in such a situation, it may damage discs  
and internal parts. Remove the disc, connect the power  
cord of the unit to the wall outlet, turn on the unit, and  
leave it for two or three hours. After two or three hours,  
the unit will have warmed up and evaporated any moisture.  
Keep the unit connected to the wall outlet and moisture  
condensation will seldom occur.  
Be sure to remove the disc and unplug the AC power cord from  
the outlet before carrying the unit  
.
On Safety  
Notes on cleaning  
Do not handle the AC power cord with wet hands and do  
not put your fingers or objects into the unit.  
When connecting or disconnecting the AC power cord,  
grip the plug and not the cord itself. Pulling the cord may  
damage it and create a hazard.  
When you are not going to use the unit for a long period of  
time, disconnect the AC power cord.  
Use a soft, dry cloth for cleaning.  
For stubborn dirt, soak the cloth in a weak detergent  
solution, wring well and wipe. Use a dry cloth to wipe it  
dry. Do not use any type of solvent, such as thinners and  
benzene, as they may damage the surface of the unit.  
If you use a chemical saturated cloth to clean the unit,  
follow that product’s instructions.  
On Recycling  
Inspection and Maintenance  
This unit’s packaging materials are recyclable and can be  
reused. Please dispose of any materials in accordance with  
your local recycling regulations.  
Batteries should never be thrown away or incinerated but  
disposed of in accordance with your local regulations  
concerning chemical wastes.  
This unit is a high technology, precision device. If the  
optical pick-up lens and disc drive parts become dirty or  
worn down, the picture quality may be reduced. To avoid  
reduction in picture quality, it is recommended that regular  
inspection and maintenance (cleaning or parts replacement)  
be performed every 1,000 hours of use. For further details,  
contact your nearest consumer electronics dealer.  
 
7
NOTES ON DISCS  
On handling discs  
On cleaning discs  
Do not touch the playback side of the disc.  
Fingerprints and dust on the disc cause picture and sound  
deterioration. Wipe the disc from the center outwards with  
a soft cloth. Always keep the disc clean.  
Playback side  
Do not attach paper or tape to discs.  
If you cannot wipe off the dust with a soft cloth, wipe the  
disc lightly with a slightly moistened soft cloth and finish  
with a dry cloth.  
Do not use any type of solvent such as thinner, benzine,  
commercially available cleaners or antistatic spray for vinyl  
LPs. It may damage the disc.  
On storing discs  
Do not store discs in a place subject to direct sunlight or  
near heat sources.  
Do not store discs in places subject to moisture and dust  
such as a bathroom or near a humidifier.  
Store discs vertically in a case. Stacking or placing objects  
on discs outside of their case may cause warping.  
Trademarks  
Symbio is a trademark of Toshiba America Information  
Systems, Inc.  
ActiveX is a trademark of Microsoft Corporation.  
Manufactured under license under U.S. Patent Nos:  
5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,392,195;  
AVCHD Related Logos are trademarks of Panasonic  
Corporation and Sony Corporation.  
7,272,567; 7,333,929; 7,212,872  
worldwide patents issued pending. DTS-HD, the  
Symbol, & DTS-HD and the Symbol together are registered  
trademarks DTS-HD Master Audio Essential is a  
&
other U.S. and  
&
Blu-ray DiscTM, Blu-rayTM, BD-LiveTM, BONUSVIEWTM, and  
the logos are trademarks of the Blu-ray Disc Association.  
&
|
trademark of DTS, Inc. Product includes software. © DTS,  
Inc. All Rights Reserved.  
Cinavia is a Verance Corporation trademark.  
CinemaNow is a registered trademark of BBY Solutions,  
Inc.  
ENERGY STAR and the ENERGY STAR mark are registered  
U.S. marks.  
DLNA®, DLNA & Design®, DLNA CERTIFIED® and DLNA  
CERTIFIED  
&
Design® are trademarks or registered  
trademarks of Digital Living Network Alliance. All rights  
reserved. Unauthorized use is strictly prohibited.  
The terms HDMI and HDMI High-Definition Multimedia  
Interface, and the HDMI Logo are trademarks or registered  
trademarks of HDMI Licensing LLC in the United States and  
other countries.  
“DVD Video Logo” is a trademark of DVD Format/Logo  
Licensing Corporation.  
Hulu Plus is a trademark of Hulu, LLC.  
Manufactured under license from Dolby Laboratories.  
Dolby and the double-D symbol are trademarks of Dolby  
Laboratories.  
 
8
YouTube is a registered trademark of Google Inc.  
The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-  
Fi Alliance. The Wi-Fi Protected Setup Identifier Mark is a  
mark of the Wi-Fi Alliance.  
Wi-Fi®, Wi-Fi DirectTM  
registered marks of the Wi-Fi Alliance.  
,
and MiracastTM are marks or  
Oracle and Java are registered trademarks of Oracle and/  
or its affiliates. Other names may be trademarks of their  
respective owners.  
Windows Media is either registered trademark or  
trademark of Microsoft Corporation in the United States  
and/or other countries.  
a
Netflix is a registered trademark of Netflix, Inc.  
Pandora is a registered trademark of Pandora Media, Inc.  
All other brand and product names are trademarks or  
registered trademarks of their respective companies.  
Picasa is a trademark of Google Inc.  
VUDU is a registered trademark of VUDU, Inc.  
“x.v.Color” and “x.v.Color” logo are trademarks of Sony  
Corporation.  
 
Introduction  
9
Introduction  
Safety icons  
This guide contains safety instructions that must be observed to avoid potential hazards that could result in  
personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified  
according to the seriousness of the risk, and icons highlight these instructions as follows:  
Indicates an imminently hazardous situation which, if not avoided, will result in death or  
serious injury.  
Indicates a potentially hazardous situation which, if not avoided, could result in death or  
serious injury.  
Indicates a potentially hazardous situation which, if not avoided, may result in minor or mod-  
erate injury.  
Indicates a potentially hazardous situation which, if not avoided, may result in property  
damage.  
Provides important information.  
Package contents  
Remote control (SE-R0431) with batteries (1 set of 2 AAA)  
Quick Start Guide  
Warranty information  
Feature highlights  
High-Definition  
Watch high-definition content disc with HDTV (High Definition Television). Connect it through a high speed  
HDMITM cable. You can enjoy excellent picture quality up to 1080p resolution with the frame rate of 24 frames  
per second with progressive scan output.  
BD-LiveTM  
Connect this player to the movie studios website via the LAN jack to access a variety of up-to-date content  
(e.g. refreshed previews and exclusive special features).  
Blu-ray DiscTM Java  
Blu-ray DiscTM Java(BD-J) Application the BD-ROM format supports Java for interactive functions. “BD-J”  
offers content providers almost unlimited functionality when creating interactive BD-ROM titles.  
DVD Upconversion for enhanced picture quality  
Your current DVD will look even better than before thanks to video upconversion. Upconversion will increase  
the resolution of a standard definition DVD to near high definition up to 1080p over an HDMITM connection.  
The picture will be less jagged and more realistic for a near high-definition experience.  
Enjoy your content on different kinds of media  
Full backwards compatibility with Blu-ray Disc™, DVD and CD ensures that you can continue to enjoy your  
current audio-video collection.  
Additionally, you can view JPEG digital pictures or listen to MP3 or Windows Media™ Audio music files.  
 
Introduction  
10  
PIP (Picture-In-Picture)  
Some Blu-ray™ videos have the PIP function which enables you to display the secondary video in the  
primary video. You can call up the secondary video by pressing PIP on the remote whenever the scene  
contains the secondary video.  
Pop up menu  
Some Blu-ray™ videos have pop-up menu which is a navigation menu that can be called up and be operated  
on the TV screen without interrupting the playback. You can call up the pop-up menu by pressing POP UP/  
MENU or TOP MENU on the remote. Contents in the pop-up menu vary depending on the disc.  
Playing back AVCHD™ files  
This player supports playback of AVCHD™ format files (new format for high definition video camcorders)  
recorded on disc. Your high definition personal archive is playable in HD quality.  
x.v.Color®  
This player supports playback of video content on discs recorded with “x.v.Color®” technology. To watch this  
video content with the “x.v.Color®”, a TV or other display device supporting both video image reproduction  
using the “x.v.Color®” standard and capable of manually switching its color setting is required. Refer to the  
User’s Guide of your display device for further information.  
Wi-Fi CERTIFIED®  
The Wi-Fi CERTIFIED® logo is an assurance that Wi-Fi® Alliance has tested a product in numerous  
configurations and with a diverse sampling of other devices to ensure compatibility with other Wi-Fi  
CERTIFIED® equipment that operates in the same frequency band. (For BDX3400KU model only).  
Easy and simple connection to your HDTV via HDMITM  
:
Connect this player to your HDTV with one single HDMITM (High-Definition Multimedia Interface) cable. It is  
recommended to use a High Speed HDMITM Cable for better compatibility. The high definition video output  
signal will be transferred to your HDTV without conversion to analog signals, so you will get excellent picture  
and sound quality.  
Media box capabilities:  
Open Browser - with HTML5 video and audio codecs allow you to explore the web, search for, bookmark,  
and browse your favorite sites to enjoy the content you want, with simple, intuitive navigation.  
ePortal page - is easy to navigate and provides graphical access to a wide variety of services.  
Remote server access  
Built-in Wi-Fi® and MiracastTM - includes peer-to-peer wireless technologies to allow direct wireless  
connection between the player and MiracastTM certified mobile devices. (For BDX3400KU model only)  
MediaShare - provides a simple graphic interface to quickly access and share videos, music, and image  
files across your home network and the other connected devices through the My Videos, My Photos, and  
My Music icons on the ePortal page.  
Media Apps & Services - connects you to entertainment apps and to family and friends.  
Apps available through the player may be changed or removed at any time. Not all operating  
system apps may be compatible with the player. Services depicted in the document and  
provided through the player may not be available to you in your region. Please check your  
individual device for app compatibility.  
 
Symbio™ Media Box and Blu-ray Disc™ Player controls  
11  
Symbio™ Media Box and Blu-ray Disc™ Player controls  
Front panel  
1
2
3
4
5
6
7
(Sample Illustration) Front panel controls  
Item:  
Description:  
Disc tray  
Function:  
Loads a disc into the disc drive.  
Receives the IR signal from the remote control.  
1
2
3
4
5
6
IR Sensor  
Opens or closes the disc tray  
.
Stops playback.  
Playback/pause.  
POWER  
Turns the power on (indicator grows green) or restores the unit to the  
standby mode (indicator is off).  
7
USB jack  
Connects a USB device.  
To completely turn the player off, you must unplug the AC power cord.  
Back panel  
1
2
3
4
(Sample Illustration) Back panel connections  
Item:  
Description:  
Function:  
1
2
3
AC power cord  
COAXIAL DIGITAL jack  
HDMI OUT jack  
Connects to a standard AC outlet.  
Outputs digital audio signals when connecting the coaxial digital cable.  
Outputs video/audio signals to a connected TV, monitor or AV receiver/  
amplifier.  
Connects to a TV, monitor or AV receiver/amplifier equipped with  
HDMITM input.  
4
LAN jack  
Connects to network capable external devices.  
 
Using the Remote Control  
12  
Remote control buttons  
Only the buttons used to operate the player are described in this section. For the HDMITM CEC Control functions, see  
“HDMITM CEC Control” on page 27.  
REMOTE SIGNAL EMITTER  
• Point remote control to the sensor on  
the front panel  
OPEN/CLOSE  
• Opens/Closes the disc tray  
POWER  
• Turns the unit to ON or standby mode  
Number Buttons  
• Enters track/chapter title numbers/  
password numbers directly  
GOTO  
• Accesses a title, chapter, track or  
playing time  
OSC  
• Accesses On Screen Control menu  
TOP MENU  
• Displays the disc title during playback  
PIP (Picture in Picture)  
• Switches on or off the secondary video  
POP UP/MENU  
• Displays a menu included on some  
Blu-ray Disc™/DVD video discs  
Clear  
• Clears an entry, bookmark, and/or  
program you have set  
REV/  
FWD  
• Fast reverse or fast forwards playback  
PLAY/PAUSE  
SKIP  
/
• Skips to previous/next chapter/ title/  
track  
• Starts or pauses playback  
STOP  
• Stops playback  
HOME  
• Displays the ePortal Home Screen  
SETTING  
/
/
/
• Displays the setup screen  
EXIT  
• Exits the current menu  
STEP/SLOW  
• Moves within on-screen menus to  
select or adjust programming options.  
• Press  
rotate the current photo track, but the  
JPEG playback will be paused.  
OK  
• Selects or confirms the highlighted  
items on screen  
/
during JPEG playback to  
• Advances the picture frame by  
frame during pause mode  
• Advances in a slow forward speed  
during normal playback  
RETURN  
PROGRAM  
• Accesses program list  
DIGEST  
• Returns to previous menu  
NETFLIX  
• Launches the Netflix® application on-  
screen.  
• Accesses JPEG thumbnail view  
during playback  
ZOOM  
• Zooms out/in  
AUDIO  
• Selects the sound stream; press  
repeatedly to select different audio  
streams available in your disc.  
2nd. AUDIO  
BOOKMARK  
• Bookmarks at any point during  
playback.  
• Switches the secondary audio of  
secondary video (PIP) to on/off.  
ANGLE  
• Switches the camera angle during  
playback  
REPEAT  
• Selects various repeat modes  
DISPLAY  
SUB (Subtitle)  
• Displays subtitles; press repeatedly  
to select different subtitles available  
in your disc  
REPEAT A-B  
• Repeats from A to B  
• Displays operating status  
 
Using the Remote Control  
13  
Installing the batteries  
Install the batteries (AAAx2), matching the polarity indicated inside battery compartment of the remote  
control.  
1 Slide the battery cover down.  
(Sample Illustration) Remote control - Opening the battery cover  
2 Insert two AAA batteries.  
Make sure to match the polarity marks (+ / -) on the batteries to the marks indicated in the battery  
compartment.  
(Sample Illustration) Remote control - inserting the batteries  
3 Replace the battery cover.  
Do not expose batteries to excessive heat such as sunshine, fire, etc.  
Dispose of batteries in a designated disposal area.  
Always consider the environment when disposing of batteries.  
Always follow applicable laws and regulations.  
If the remote does not operate correctly, or if the operating range is reduced, replace the  
batteries.  
Always replace both batteries with new ones. Never mix battery types or use new and used  
batteries together.  
Always remove batteries from the remote if they are dead or if the remote control is not to be  
used for an extended period of time.  
This prevents battery acid from leaking into the battery compartment.  
Using the remote control  
For optimum performance, aim the remote control directly at the player and make sure there are no  
obstructions between the remote control and the player. The maximum operable ranges from the unit are  
as follows.  
- Line of sight: approx. 7 m  
- Either side of the centre: approx. 5 m within 30°  
- Above: approx. 5 m within 30°  
- Below: approx. 5 m within 30°  
5 m  
7 m  
5 m  
(Sample Illustration) Remote control effective range  
 
Using the Remote Control  
14  
Do not expose the remote sensor to a strong light source such as direct sunlight or other  
illumination. This can damage the sensor resulting in the inability to operate the player via  
the remote control.  
Do not drop or expose the remote control to electric shock.  
Do not expose the remote control excessively hot or humid places to avoid moisture  
condensation.  
Do not spill water or place anything wet on the remote control.  
Do not open the remote control unit (other than the battery door).  
If the remote control is not going to be used for a long period of time, remove the batteries to  
avoid damage caused by battery leakage corrosion.  
Direct the remote control at the remote sensor of SymbioTM Media Box and Blu-ray Disc™  
player.  
When using the remote control, press the buttons at intervals of approximately 1 second to  
ensure the correct mode of operation.  
 
SymbioTM Media Box and Blu-ray DiscTM Player connections  
15  
Symbio™ Media Box and Blu-ray Disc™ Player connections  
It is important to connect the player to the Internet and AV devices first, before connecting the player to AC  
power.  
Connecting to a TV  
Connect a HDMITM cable from the HDMITM output jack on this player to the HDMITM input jack on the TV.  
An HDMITM cable carries both video and audio signals. If you wish to use TV speakers, you do not need to  
make an additional audio connection.  
HDMITM cable  
(not supplied)  
(Sample Illustration) Connecting to a TV - HDMITM cable  
Connecting to the digital AV receiver/amplifier  
Route the sound from this player to the AV receiver/amplifier/sound system to enhance audio output.  
Connect a coaxial cable from the COAXIAL jack on this player to the COAXIAL jack on the device.  
Digital AV receiver/  
amplifier  
Digital audio coaxial cable  
(not supplied)  
(Sample Illustration) Connecting to a digital AV receiver/amplifier  
Connecting to network  
Your Symbio™ Media Box and Blu-ray Disc™ Player can be connected to your home network:  
Using a wired network provides the best performance because the attached device and player are  
connected directly to the network and are not subject to radio frequency interference.  
To use a wireless connection, you can connect through a wireless LAN adapter and a wireless access  
point or router (for BDX2400KU model).  
To use a wireless connection, you can connect through the built-in wireless device and a wireless access  
point or router (for BDX3400KU model).  
 
Symbio™ Media Box and Blu-ray Disc™ Player connections  
16  
Connecting via wired router  
Connect the network cable from the LAN jack on the player to the LAN jack on the network system’s hub or  
broadband router.  
hub or broadband router  
LAN cable (not supplied)  
(Sample Illustration) Connecting to a wired router  
Do not connect a modular phone cable to the LAN jack.  
Because there are various connection configurations, follow the instructions from your  
telecommunication carrier or Internet service provider.  
Connecting via a USB Wi-Fi® adapter and wireless access point or  
router - for BDX2400KU model  
Connect the TOSHIBA’s USB Wi-Fi® adapter to the USB jack on the right side of the player, and set the  
wireless network options. No physical connection to the wireless router is necessary.  
Wireless  
access point  
TOSHIBA’s Wi-Fi® adapter  
(not supplied)  
(Model name: WLM-12NB1)  
(Sample Illustration) Connecting to a wireless router  
1. Configure your player to access the wireless access point or router.  
2. The network configuration and connection method may vary depending on the equipment in use and the  
network environment. For the best wireless performance, we recommend using an IEEE 802.11n Wi-Fi®  
CERTIFIED network (access point or wireless router).  
 
SymbioTM Media Box and Blu-ray DiscTM Player connections  
17  
A USB Wi-Fi® adapter is required for a wireless connection.  
This unit is compatible with TOSHIBA’s USB Wi-Fi® adapter only (Model name: WLM-12NB1).  
For detailed information, please refer to the device’s User’s Guide for WLM-12NB1.  
Connecting via the built-in Wi-Fi® device and a wireless access point  
or router - for BDX3400KU model  
Your Media Box and Blu-ray DiscTM player has an integrated Wi-Fi® device and antenna. No physical  
connection to the wireless router is necessary.  
Wireless access point  
(Sample Illustration) Connecting to a wired router  
1. Configure your player to access the wireless access point or router.  
2. The network configuration and connection method may vary depending on the equipment in use and  
the network environment. Your Media Box and Blu-ray DiscTM player is equipped with an IEEE 802.11n  
wireless module, which also supports the 802.11a/b/g/n standards. For the best wireless performance, we  
recommend using an IEEE 802.11n Wi-Fi® CERTIFIED network (access point or wireless router).  
Connecting USB device  
Connect the USB device to the right side of the player. The USB jack supports USB device, TOSHIBA’s USB  
Wi-Fi® adapter (Model name: WLM-12NB1) and 4 port USB Hub.  
A USB device provides an additional memory to software upgrade and enjoy BD-LiveTM bonus content. You  
can also enjoy playing back MP3/JPEG/MPEG4 files stored on the USB device.  
USB device  
(Sample Illustration) Connecting a USB device  
To enjoy BD-Live™ bonus content, as your local storage, use a 1 GB or larger USB device.  
For some Blu-rayTM discs with BD-LiveTM feature, you may need to plug in the USB device  
before loading the disc. Otherwise, the disc may not play.  
TOSHIBA does not guarantee 100% compatibility with all USB devices.  
USB-Hub is used when using USB device and TOSHIBA’s USB Wi-Fi® adapter  
together.  
 
Symbio™ Media Box and Blu-ray Disc™ Player connections  
18  
Connecting Power  
Connect the AC power cable to the electrical wall outlet. The player can now be set up for use.  
Before connecting the AC power cord, ensure you have completed all other connections.  
Ensure that the power supply voltage corresponds to the voltage printed on the back of the  
unit or your player may be damaged.  
The type plate is located on the back of the unit.  
 
Blu-ray Disc™ playback  
19  
Blu-ray Disc™ playback  
Before you play a disc in the player, read the following information.  
CinaviaTM Notice  
This product uses CinaviaTM technology to limit the use of unauthorized copies of some  
commercially-produced film and videos and their soundtracks. When a prohibited use of  
an unauthorized copy is detected, a message will be displayed and playback or copying will  
be interrupted.  
More information about CinaviaTM technology is provided at the CinaviaTM Online Consumer  
CinaviaTM by mail, send a postcard with your mailing address to: CinaviaTM Consumer  
Information Center, P.O. Box 86851, San Diego, CA, 92138, USA.  
Disc and file playback  
This player is compatible with the following discs/files.  
To play a disc/file, make sure that it meets the requirements for region codes and color systems as described  
below. You can play discs that have the following logos.  
Other disc types are not guaranteed to play back.  
Logos:  
Playable discs:  
Blu-ray Disc™-Video  
BD-ROM Ver 2.0 - Profile1.1 (True BD Player and PinP, Virtual File System  
Support)  
BD-R Ver 1.1/1.2/1.3 - BD-ROM mode (BDMV Recording)  
BD-RE Ver 2.1 - BD-ROM mode (BDMV Recording)  
DVD-ROM (single/dual layer)  
DVD-RW (single layer at finalized disc)  
DVD-R (single/dual layer at finalized disc)  
CD-DA (audio CD)  
CD-RW  
CD-R  
DTS®-CD  
-
 
Blu-ray Disc™ playback  
20  
Playable files:  
Media:  
AVCHD™  
DVD-RW/-R, USB  
MP3  
BD-RE/-R, DVD-RW/-R, CD-RW/-R, USB  
Windows Media™ Audio  
JPEG  
MPEG2-PS/TS  
AVI  
ASF  
MKV  
MP4  
This player cannot play disc content that is protected by Windows Media™ Digital Rights Management  
(DRM).  
Region codes  
This player has been designed to play back Blu-ray™ video with region “A” and DVD-video with region “1”  
or “ALL.” You cannot play back Blu-ray™ video or DVD-video that are labeled for other regions. Look for the  
symbols on your Blu-ray™ video or DVD-video.  
If these region symbols do not appear on your Blu-ray™ video or DVD-video, you cannot play back the disc in  
this player. The letter or number inside the globe refers to region of the world. A Blu-ray™ video or DVD-video  
labeled for a specific region can only be played back in the player with the same region code.  
Blu-ray™ video  
DVD-video  
Color system  
Blu-ray™ video and DVD-video are recorded in different color systems throughout the world.  
The most common color system is NTSC (which is used primarily in the United States and Canada).  
 
Blu-ray Disc™ playback  
21  
Setting up the player  
Find the correct viewing input  
1 Press the  
button to turn on this product.  
2 Turn on the TV and switch to the correct video-in input (refer to the TV user’s manual for instructions on  
how to select the correct input).  
Initial Setting  
When you turn on this unit for the first time, or restore all settings to factory defaults, the system will prompt  
you to perform the initial setup.  
1 Follow the on-screen instructions to customize the following settings to your preference:  
OSD Language  
For more information, please see the “Language Setting” section on page 29.  
Resolution  
For more information, please see the “Resolution” section on page 31.  
Aspect ratio  
For more information, please see “TV Screen” section on page 31.  
2 After selecting the settings, press OK to confirm and exit.  
SETTING menu  
Press the SETTING button on the remote control to display the setup screen.  
For more information, please see the “Customizing” on page 26.  
ePortal Home  
Press the HOME button on the remote control to display the ePortal Home screen when there is no disc  
playing or the player is in Stop mode.  
For more information, please see the “Navigating the ePortal Menu” on page 32.  
Basic playback  
When you wish to view a disc, turn the TV on and select the video input connected to the Symbio™ Media  
Box and Blu-ray Disc™ Player.  
1 Press the button on the front panel or the remote control; your Symbio™ Media Box and Blu-ray Disc™  
Player will turn on.  
2 Turn the TV on and then select the input setting on the TV that matches the connection method you used  
to connect your player.  
3 Press the  
OPEN/CLOSE button on the remote control to open the disc tray.  
4 Place a disc on the disc tray with the label facing up, and then press the  
the disc tray.  
OPEN/CLOSE button to close  
The disc loading time depends on the types of disc you are loading.  
5 After loading a disc, the playback starts automatically.  
6 If a Blu-rayTM Disc or DVD menu is displayed, use cursor buttons to select PLAY. Then, press the OK  
button to confirm.  
7 To eject the disc, press the  
OPEN/CLOSE button.  
Pause playback  
1 Press the  
button to pause playback. The sound will be muted.  
2 Press the  
button to resume the playback.  
Still Off  
1 Press the  
button to continue to playback when in still off mode.  
 
Blu-ray Disc™ playback  
22  
Stop playback  
1 Press the STOP button once to go to resume mode, the TV screen will show the resume logo.  
Press the button to resume playback from the point where playback is stopped.  
2 Press the STOP button twice to stop the playback completely and the setup screen appears.  
Use the  
/
button to select BD/DVD, and press the OK button to begin playback from the beginning of  
the disc.  
Not all Blu-rayTM Discs support the resume feature.  
Fast Forward and Fast Reverse  
1 Press the  
button to fast forward through the disc. The fast forward speed changes based on how  
many times you pressed the button.  
2 Press the  
button to fast reverse through the disc. The fast reverse speed changes based on how  
many times you pressed the button.  
The speed will increase through the following sequence: 2X, 4X, 8X, 16X, 32X.  
3 Press the  
button to resume normal playback.  
Instant Search and Instant Replay  
1 During playback, press and hold the  
button, you can search 30 seconds forward.  
2 During playback, press and hold the  
before.  
button, you can instant replay the content from 10 seconds  
Previous and Next  
1 During playback, press the  
previous chapter or track.  
button to skip back to the beginning of the current chapter or track or the  
2 Press the  
button during playback will allow you to skip the playback to next chapter or track.  
Slow Forward  
1 Press the STEP/SLOW button during normal playback. The slow forward speed is 1/16 in default.  
2 To change slow forward speed, press the STEP/SLOW button repeatedly, and the slow forward speed will  
be changed in the following sequence: 1/16, 1/8, 1/4, 1/2, normal.  
3 To exit slow forward mode and return to normal playback, press the  
button.  
Step Forward  
Use this feature to help you to enjoy the video frame by frame.  
1 Press the  
2 Press the STEP/SLOW button repeatedly to advance the picture frame by frame.  
3 Press the button to resume normal playback.  
button during normal playback, then playback will change to pause state.  
Advanced Playback  
GOTO  
During playback,  
1 Press the GOTO button to edit Title, Chapter, and Time.  
2 Press the  
/
button and OK on the remote control to select Title, Chapter, or Time.  
3 Press the numeric buttons or  
location.  
/
button and then press OK. The playback will skip to the desired  
4 For Time Search, press the  
/
button to select TT (Title) or CH (Chapter) time search.  
 
Blu-ray Disc™ playback  
23  
TOP MENU  
You may press the TOP MENU button at any time, and the Blu-ray DiscTM or DVD video disc playback will  
display the disc menu.  
POP UP/MENU  
During Blu-ray DiscTM playback, press the POP UP/MENU button to display the disc title, and the playback  
will not be stopped even if the menu is displayed on the screen.  
RETURN  
Press the RETURN button to return to the previous on-screen menu in the setup menu such as External  
Memory Information, Parental Control, etc.  
During MP3/JPEG playback, press the RETURN button once, it will return back to Media Center page.  
PROGRAM  
During DVD/CD playback, you can press the PROGRAM button to edit the sequence of the playlist.  
DIGEST  
During playback of JPEG disc, press the DIGEST button to view a page of 12 thumbnail images.  
1 Use the / /  
/
buttons to select an image.  
2 Press OK to view the selected image in full-screen and subsequent images will be displayed one after  
another automatically.  
3 Press the  
/
buttons to view the previous or next thumbnail screen.  
ZOOM  
Press the ZOOM button repeatedly to Zoom in/out playback in the video.  
Zoom mode : Zoom 2x -> Zoom 3x -> Zoom 4x -> Zoom 1/2 -> Zoom 1/3 -> Zoom 1/4.  
BOOKMARK  
During playback, press the BOOKMARK button to add the bookmark; press and hold for a few seconds to  
display the list of bookmarks that were previously added on the screen, then you can press the OK button to  
select the bookmark or the CLEAR button to delete the bookmark.  
SUB  
Press this button repeatedly and the screen will display “X/XX XXX” or “Off”. The “X” indicates the current  
number of this language; “XX” indicates the total number of subtitle languages on the disc; “XXX” indicates  
the language.  
The number of available languages depends on the disc.  
AUDIO  
Press the AUDIO button on the remote control to select the audio streams that set within the Blu-rayTM or  
DVD disc.  
The screen will display:  
AUDIO: X / XX XXX XXXX  
“X” - The current audio stream number  
“XX” - The total number of audio streams  
“XXX” - Audio Language  
“XXXX” - Audio Technology  
ANGLE  
During playback, press this button to change the angle of the picture. The screen will display “Angle X/X.”  
The first “X” indicates the current number of angle, and the second “X” indicates total number of angles.  
Not all Blu-rayTM or DVD has the multi-angle feature. The screen will take approximately 5 seconds to  
change.  
 
Blu-ray Disc™ playback  
24  
REPEAT  
Press the REPEAT button repeatedly to select different repeat modes.  
Blu-ray DiscTM: Repeat Chapter and Title.  
DVD: Repeat Chapter, Title and All.  
CD-DA/JPEG/MP3: Repeat Track and All.  
A-B  
To play certain sections within the video or song, press the A-B button to set the start point. Then, press  
the A-B button again to set the end point and complete the setting. The selected section will be played  
repeatedly.  
Press the A-B button the third time to cancel this function.  
The end point cannot be set until 5 seconds of playback has elapsed from the start point.  
Not all Blu-rayTM Discs support the repeat A-B feature.  
DISPLAY  
Press the DISPLAY button and the screen will display some information about disc, such as: Title number,  
Chapter number, Track number, Elapsed Time, Audio, Angle, and Subtitle languages. Press this button again  
to turn off the information display.  
OSC  
Press the OSC button to open the On Screen Control menu during playback. In this menu, you can access  
the playback-related control options.  
The on screen control contains following items:  
Title: The title in current playback/titles in total. Select your desired title to play.  
Chapter: The chapter in the current playback/chapters in total. Select your desired chapter to  
playback.  
Time: View the elapsed/remaining playback time of title/chapter. Use the  
/
button to view: the  
elapsed playback time of title, the remaining playback time of title, the elapsed playback time of  
chapter, and the remaining playback time of chapter.  
Mode: Selects playback mode among shuffle, random, and normal.  
Audio: The Blu-ray DiscTM/DVD disc’s soundtrack language. Use the  
available in the disc and select your desired Audio type.  
Angle: The angle view of current playback/the angles in total. Use the  
desired angle view.  
/
button to view the audio  
button to select your  
/
Subtitle: The Subtitle in current playback.  
Use the  
/
button to view the subtitles available in the disc and select your desired subtitle type or  
turn it off.  
Subtitle Style: When you play the Blu-ray DiscTM or DVD disc and if it has an external subtitle, you will  
see it in OSC menu.  
Secondary Video: Turns On/Off the secondary video.  
Secondary Audio: Turns On/Off the secondary audio.  
Bitrate: Use the  
/
button to select audio or video bitrate.  
Still Off: Closes the Still feature.  
For some Blu-ray DiscTM or DVD discs, a certain video picture will be frozen as a still picture during the  
process of playback to let the user has a better view of certain picture. To continue playback, select Still  
Off.  
Instant Search: Instant search 30 seconds forward.  
Instant Replay: Replays the content from 10 seconds before.  
The specified operation for each item will vary with disc types. And some items are available only  
when the disc is supportable.  
 
Blu-ray Disc™ playback  
25  
PIP  
Some Blu-ray™ discs have the PIP function enabling you to display the secondary video in the primary video.  
You can call up the secondary video by pressing the PIP button when the scene contains the secondary  
video. See the documentation that came with the disc for playback instructions.  
1 Turn on secondary video by pressing the PIP button.  
2 Press the 2nd. AUDIO button to turn on the audio for the secondary video (PIP).  
In order to hear the secondary audio, the PIP feature on the disc must be turned on.  
3 Press the PIP button again to turn off the secondary video.  
Primary video  
Secondary video  
with Secondary  
Audio  
(Sample Illustration) PIP view function  
This function is not available when the primary video is played in Search, Slow-Motion, or Frame-by-Frame  
or Fast Forward/ Reverse mode.  
To listen to the secondary audio, the digital audio output must be set to “Bitstream”, “Re-encode” or “PCM”.  
Otherwise, only the primary audio can be heard.  
Not all the Blu-ray™ discs can support this function.  
High Definition PIP (Second Video) is not supported.  
Playing MP3/JPEG/MPEG4 files  
You can play MP3/JPEG/MPEG4 files that have been recorded on a disc or a or a USB device on the  
player.  
1 Load a disc or insert a USB device that contains MP3/JPEG/MPEG4 files.  
2 On the setup screen, press the  
/
button to select Video, Music, or Photo, and then press OK.  
The Media Center menu appears on the screen.  
(Sample Illustration) Media Center menu  
3 Press the  
4 Press the  
/
/
button to select Data Disc or USB1, and press OK.  
button to select a file (or folder) and press OK or  
to start playback.  
It should match the selection on the setup screen. (If you selected Video on the setup screen, you also  
should select Video here.)  
Not all media formats are supported.  
 
Customizing  
26  
Customizing  
This section describes the various setting options of this Symbio™ Media Box and Blu-ray Disc™ Player.  
If the setup option is greyed out, it means the setting cannot be changed at the current state.  
1 Press the SETTING button in stop mode to display the setup screen.  
2 Press OK to enter the Setting menu.  
3 Use the  
/
button to select an option and press OK.  
4 Press the button or the RETURN button to return to the previous menu.  
(Sample Illustration) General operations settings  
Audio Setting  
1 In the Setting menu, use the  
/
button to select Audio and press OK.  
2 Press the  
/
button to select an option and press OK.  
3 Use the  
/
button to select the desired audio setting and press OK.  
4 Press the button or the RETURN button to return to the previous menu.  
SPDIF  
When you connect an audio system to the COAXIAL DIGITAL output jack, the options are:  
Bitstream: Selects Bitstream output if your receiver SPDIF (Coaxial) IN supports Dolby® or DTS® or  
PCM audio signal.  
PCM: Selects PCM output if your receiver SPDIF (Coaxial) IN only supports PCM stereo audio  
signal.  
Re-encode: Selects Re-encode output if your receiver SPDIF (Coaxial) IN supports Dolby® or DTS®  
and you want to hear both PIP audio and the movie audio on Blu-ray™ video.  
Off: No audio will be output via COAXIAL DIGITAL output jack.  
HDMI  
When you connect an HDMITM device to the HDMI OUT jack, the available options are:  
Bitstream: Selects Bitstream output if your receiver HDMI IN supports Dolby® or DTS® or PCM audio  
signal.  
PCM: Selects PCM output if your receiver HDMI IN only supports PCM audio signal.  
Re-encode: Selects Re-encode if your receiver’s HDMI IN supports Dolby® or DTS® and you want to  
hear both PIP audio and movie audio on Blu-ray™ video.  
Off: No audio will be output via HDMI OUT jack.  
 
 
Customizing  
27  
Down_samp  
Select the digital audio signal sampling frequency. (Only available on Coaxial)  
48k: For discs recorded at sampling rate of 48 kHz.  
96k: For discs recorded at sampling rate of 96 kHz.  
192k: For discs recorded at sampling rate of 192 kHz.  
Dolby DRC  
Select the Dynamic Range Control (DRC) mode which makes it available to listen to a movie at a low volume  
without losing sound clarity.  
Off: Non-dynamic range compress.  
On: Dynamic range compress.  
Auto: Adjust the DRC according to input audio.  
The setting of Auto is effective for Dolby® TrueHD.  
Stereo Down Mix  
Select whether to downmix the multi-channel audio into fewer channels.  
Stereo: Downmixes the multi-channel audio into two channel stereo. Choose when the unit is  
connected to equipment that does not support virtual surround function such as Dolby® Pro Logic.  
Surround Encoded (LtRt): Downmixes the multichannel audio into surround compatible stereo.  
Choose when the unit is connected to equipment that supports virtual surround function such as Dolby®  
Pro Logic.  
System Setting  
1 In the Setting menu, use the  
/
button to select System and press OK.  
2 Use the button to select an option and press OK.  
/
3 Press the button or the RETURN button to return to the previous menu.  
Screen Saver  
The screen saver helps protect the TV screen. You can turn on/off the screen saver mode.  
On: Sets the screen saver active after approximately 5 minutes without operation.  
- The unit will switch to standby mode if there is no operation after the screen saver is engaged for  
approximately 20 minutes.  
Off: Turns off the screen saver mode. The unit will not switch to standby mode automatically.  
Disc Auto Play  
Turns On or Off the disc automatic playback switching mode.  
On: The disc playback automatically after loading.  
Off: Turn off disc auto play mode.  
CEC  
This feature uses CEC (Consumer Electronics Control) technology and allows you to control Toshiba HDMI™  
CEC compatible devices from the player’s remote control via the HDMI™ connection.  
On: Turns on HDMITM CEC features.  
With CEC on, pressing SETTING, PLAY/PAUSE button will power on the TV when the TV is in the  
standby mode. When you turn the TV off, this player will automatically turn off.  
Off: Disables HDMITM CEC features.  
Load Default  
Resets all settings of the player to initial default state.  
- Follow the instructions on the TV screen to confirm the default setting operation.  
 
 
Customizing  
28  
Deactivate Setting  
To apply the deactivation, unplug the player after operating deactivation.  
Upgrade  
This option allows you to update your players software via a Disc, USB Storage or Network.  
External Memory  
The External Memory can be used in the BD-LiveTM function. When you plug in the USB device, which has  
at least 1GB free space to play BD-LiveTM function, the Blu-ray DiscTM system creates a directory named  
BUDA automatically.  
Media Information will display the Free size.  
- Press OK to select “Fmt buda”, the data in the BUDA folder will be cleared.  
Network  
1 In the Setting menu, use the  
/
button to select Network and press OK.  
2 Press the button to select an option and press OK.  
/
3 Press the button or the RETURN button to return to the previous menu.  
Internet Connection  
Allows you to enable/disable the Internet connection.  
Interface  
This system setting allows you to choose the way to connect network via Ethernet or Wireless.  
Connection Test  
Selecting the Connection Test will cause the player to attempt to communicate with your home network and  
with a known Internet address. If both attempts are successful, your network connection should be configured  
correctly. If the player can successfully connect to your home network, but not to the known Internet address,  
your Internet service may be unavailable, or your security firewall may be blocking access of the player to  
the Internet.  
IP Setting  
Auto: Auto obtain network information.  
Manual: Manual setup network information.  
Wi-Fi DirectTM  
This allows you to configure a secured wireless network between the player and a Wi-Fi DirectTM compatible  
device (e.g. smartphone) without using an access point (for BDX3400KU model only).  
Enable: Turns on the Wi-Fi DirectTM features.  
Disable: Disables the Wi-Fi DirectTM features.  
Wi-Fi DirectTM Setting  
To scan and connect a Wi-Fi DirectTM compatible device, e.g. smartphone (for BDX3400KU model only).  
Information  
This displays all Network Information.  
BD-Live™ Connection  
Permitted: During playback of BD-Live™ disc, the disc may automatically download all information  
from appointed network.  
Partial Permitted: During playback of BD-Live™ disc, the disc may automatically download partial of  
the information from appointed network.  
Prohibited: Disable downloading information from network.  
 
 
Customizing  
29  
Media Sever Search  
The Media Sever Search function enables you to create an interoperability network with other devices for  
resource sharing based on a network. See Media Server Search on page 32 for details.  
Language Setting  
This setting allows you to choose the language for your on-screen menus and screens.  
1 In the Setting menu, use the  
/
button to select Language and press OK.  
2 Press the  
/
button to select an option and press OK.  
3 Use the  
/
button to select the preferred language.  
4 Press the button or the RETURN button to return to the previous menu.  
OSD  
Selects the on-screen menu language.  
Menu  
Selects the disc menu language.  
Audio  
Selects the audio language of your preference.  
Subtitle  
Selects your preferred subtitle language.  
Security  
1 In the Setting menu, use the  
/
button to select Security and press OK.  
2 Press the button to select an option and press OK.  
/
3 Press the button or the RETURN button to return to the previous menu.  
Change password  
Follow the instructions on the TV screen to change the password for locked discs and play restricted Blu-  
rayTM discs/DVDs.  
1
2
3
Use the number buttons to enter the four digit old password. The default password is “0000”.  
Enter the new password.  
Enter the new password again to confirm.  
If you forget the password, you can erase your current password by entering in the default password.  
Parental Control  
Restricts access to discs that are unsuitable for children. These discs must be recorded with rating.  
1
2
Use the number buttons to enter the password.  
Select a rating level, then press OK.  
1 [Kid safe] - Safe for kids  
2 [G] - All children and general guidance  
3 [PG] - Parental guidance  
4 [PG-13] - Parental guidance for children under 13  
5 [PG-R] - Parental guidance recommended  
6 [R] - Restricted viewing  
7 [NC-17] - No one 17 and under allowed  
8 [Adult] - Adult only  
 
 
Customizing  
30  
Rated discs above the level you set in Parental Control require a password to be entered.  
The ratings are country dependent. To allow all discs to play, select ‘Off’.  
Information  
1 In the Setting menu, use the  
/
button to select Information and press OK.  
2 The current Software Version, MAC Address and Netflix ESN will be displayed.  
3 Press the button or the RETURN button to return to the previous menu.  
Playback  
1 In the Setting menu, use the  
/
button to select Playback and press OK.  
2 Press the  
/
button to select an option and press OK.  
3 Use the  
/
button to select On/Off, and press OK to confirm.  
4 Press the button or the RETURN button to return to the previous menu.  
Angle Mark  
Some Blu-rayTM discs/DVDs contain the scenes recorded with multiple angles, which allow you to enjoy the  
videos with your desired angles, therefore the angle mark is displayed only when the Blu-ray Disc™/DVD  
disc is supportable for multi-angle and Angle Mark is set to ON.  
On: Displays the Angle Mark.  
Off: Hides the Angle Mark.  
PIP Mark  
The Picture -In- Picture (PIP) mode display two pictures on the TV screen at the same time, the full screen  
picture is called Main Window and the small inset window is called Sub Window. The PIP Mark is displayed  
when in PIP mode and PIP Mark is set to ON.  
On: Displays the PIP Mark.  
Off: Hides the PIP Mark.  
Secondary Audio  
On: Displays the Secondary Audio.  
Off: Hides the Secondary Audio.  
Last Memory  
If you open the disc tray or switch this Symbio™ Media Box and Blu-ray Disc™ Player to standby state  
during normal playback, the player can memorize the end playing point, the player will start playback from  
the memorized point next time.  
On: Enables Last Memory feature.  
Off: Disables Last Memory feature.  
Not all the Blu-rayTM discs can support this function.  
Display Setting  
These settings configure how the picture is displayed on the television or screen.  
1 In the Setting menu, use the  
/
button to select Display and press OK.  
2 Press the  
/
button to select an option and press OK.  
3 Use the  
/
button to select the desired option, and press OK to confirm.  
4 Press the button or the RETURN button to return to the previous menu.  
 
Customizing  
31  
TV Screen  
Select the screen format according to how you want the picture to appear on the TV.  
16:9 Full: For a disc with the aspect ratio of 4:3, the output video is stretched into 16:9 full screen.  
16:9 Normal: For a disc with the aspect ratio of 4:3, the output video is resized vertically to match what  
will be seen on the display.  
4:3 Pan&Scan: For standard TV, it displays a wide picture on the entire screen and cuts off the  
redundant portions.  
4:3 Letterbox: For standard TV, it displays a wide picture with two black borders on the top and bottom  
of 4:3 screen.  
Resolution  
Selects a video output resolution that is compatible with your TV display capability.  
Auto: Select the most suitable resolution according to the TV.  
480i, 480p, 720p, 1080i, 1080p: Select a video resolution setting that is best supported by the TV. See  
TV manual for details.  
Color Space  
Selects a predefined Colour space of picture: RGB, YCbCr, YCbCr422, Full RGB.  
HDMI Deep Color  
This feature is available only when the display device is connected by an HDMITM cable, and when it supports  
Deep Color feature.  
On: Enables HDMI Deep Color.  
Off: Disables HDMI Deep Color.  
HDMI 1080/24p  
Movies are recorded on film at a rate of 24 pictures (frames) per second. Many of the movies on Blu-ray™  
discs are placed on the discs at this frame rate. However, not all TVs can display 24 progressive frames/  
second of video. If the TV cannot display this frame rate, you need to turn off HDMI 1080/24p.  
On: Enables 1080/24p video resolution setting.  
Off: Disables 1080/24p video resolution setting.  
Video Adjust  
Brightness: Press the  
/
button to adjust the brightness of display, goes left means dark and right  
means bright.  
Contrast: Press the  
/
button to adjust the contrast of display, goes left means low contrast and right  
means high contrast.  
Hue: Press the  
/
button to adjust the Hue of display, goes left means low hue and right means high  
hue.  
Saturation: Press the  
/
button to adjust the saturation of display, goes left means low Saturation and  
right means high saturation.  
Sharpness  
Selects the level of sharpness: High, Middle, Low.  
 
 
Network functional description  
32  
Network functional description  
Media Server Search  
With this player connected to network, you can play video, music and photo files from the server.  
1 Connects this player to server network and set the Media Server Search to Enable.  
See Network on page 29 for details.  
2 Press the SETTING button to enter the setup screen and use the  
Photo, and then press OK.  
/
button to select Video, Music, or  
The Media Center menu appears on the screen.  
3 Press the  
4 Press the  
/
/
button to select Media Server list, and then press OK.  
button to a kind of media (Photo, Music, Video) and press OK.  
It should match the selection on the setup screen. (If you selected Video on the setup screen, you also  
should select Video here.)  
5 Press the  
/
button to select a file (or folder) and press OK or  
button to start playback.  
Not all media formats are supported.  
MiracastTM  
This feature allows you to enjoy videos, music and photos on your MiracastTM compatible device (e.g.  
smartphone) by using a Wi-Fi DirectTM connection without using an access point (for BDX3400KU model  
only). To use this feature:  
1
2
Turn on your MiracastTM compatible device (e.g. smartphone) and set the Wi-Fi DirectTM to On.  
Then configure the player:  
1) Enter the Network menu and set the Wi-Fi DirectTM to Enable.  
2) Then enter the Wi-Fi DirectTM Setting to scan and and select your MiracastTM compatible device,  
then press OK. For more information, please see the Network” section on page 28.  
3
4
On your MiracastTM compatible device, search for the “TOSHIBA BDPL” from the list of discovered  
devices and select it. It may take the player and the MiracastTM compatible device a few seconds to  
connect.  
After connecting successfully, you can now enjoy videos, music and photos on your MiracastTM compatible  
device from the unit.  
This player is a Miracast™ certified Wi-Fi Alliance® device; connection and/or compatibility  
issues with other Wi-Fi CERTIFIED Miracast™ devices are possible. Issues include, but not  
limited to:  
non-transfer of certain kind of data through the mirroring function of this player.  
connection errors due to functions of sending device.  
video and/or picture contents displayed on sending device may not be displayed as is  
through the player.  
depending on the Wi-Fi CERTIFIED Miracast™ devices, the connecting operation differs.  
Refer to device’s user manual.  
you cannot use the Wi-Fi CERTIFIED Miracast™ technology and have access to the  
Internet using a wireless network at the same time.  
Navigating the ePortal Menu  
A new ePortal page is easy to navigate and provides graphical access to a variety of services such as Apps,  
Open Browser, Videos, Photos, Music, Settings and others.  
You need to configure your home network before using this feature. The apps available  
through the ePortal may be changed or removed at any time. Services depicted in this User’s  
Guide and provided through the ePortal may not be available in your region and may not be  
available to you.  
 
 
Network functional description  
33  
To navigate the ePortal page:  
1 Press the HOME button on the remote control or select Portal in the setup screen to display the Home  
screen.  
2 Press the  
/
/
/
(arrow) buttons to select the desired icon and press the OK button.  
3 To close a menu, press the EXIT button.  
ePortal Home Page  
• Player Settings - customizes your player’s options.  
• Open Browser - access the Internet for searching, browsing, and bookmarking your favorite content.  
• Disc - plays the disc that is loaded into the disc tray.  
• My Videos - view your video content.  
• My Photos - view your personal photos  
• My Music - play and listen to your music.  
• Settings - customizes the ePortal settings.  
Some features require an always-on broadband Internet connection, firmware update and/or  
additional bandwidth dedicated to this product. Third party Internet services may change or  
be discontinued or restricted at any time. Toshiba makes no warranties, representations, or  
assurances about the content, availability or functionality of third-party content or services.  
Use of third party Internet services may require registration by a computer and/or payment  
of charges and membership. Not all services or content may be available on this product, in  
your country or in your language. Please see the User’s Guide on support.toshiba.com.  
Compatibility and/or performance issues are possible. Certain interactive features may not be  
supported due to compatibility, network settings or other conditions.  
Open Browser  
1
2
3
Use the  
/
/
/
(arrow) buttons to select the Open Browser icon.  
Press the OK button to enter Toshiba’s home website.  
Press the DISPLAY button on the remote control or the TAB key of USB keyboard to turn on/off the Open  
Browser menu bar. You can use the  
/
button to select Home, Search, History, Bookmark, Display,  
Tool or Exit on the Open Browser menu bar and press the OK button.  
4
Press the RETURN button on the remote control to exit and return to the ePortal Home page.  
• Home - accesses the Toshiba’s home website.  
• Go to - inputs target web address.  
• Search - inputs key words to search.  
• History - refered web site page.  
• Bookmark - adds current web site page as Favorite.  
• Display - zooms in/out the current display screen.  
Tool - clears Cookies, History, Cache or Certification.  
• Exit - exits and returns to the ePortal Home page.  
The web browser on this device:  
• may not support certain functions used in web pages.  
• may not display web pages as intended, or may not function.  
• does not support platform-dependent technologies such as ActiveX®.  
• only supports preinstalled plug-ins.  
• uses a single built-in font. Some text may not be displayed as intended.  
• does not support downloading of files or fonts.  
In addition, some web pages may exceed the memory allotment of the web browser. The web browser will  
close when this happens.  
 
Network functional description  
34  
Watching movies with CinemaNow®  
This player enables you to use the following services provided by CinemaNow®. In order to use this service,  
you must set up a user name and password.  
1
2
3
Press the HOME button on the remote control or select Portal in the setup screen to display the ePortal  
Home.  
Use the  
/ /  
/
buttons to select CinemaNow icon, and then press the OK button to enter the  
CinemaNow® main menu.  
If you don’t have a CinemaNow® account yet, visit www.cinemanow.com/bbactivate to create your  
account.  
4
5
Press the / /  
Press Accept.  
/
buttons to select ENDUSER LICENSE AGREEMENT and then press the OK button.  
The activation code is displayed on the TV screen.  
6
Visit cinemanow.com/start and enter your user name and password.  
When the player is activated, you will move to the CinemaNow® Home page.  
7
8
9
Press the  
Press the / /  
Press the  
/
button to select Store, and then press the OK button.  
buttons to select the desired title, and then press the OK button.  
button to select Rent or Buy, and then press the OK button.  
/
/
10 Press the  
/
button to select Submit Order, and then press the OK button. If you wish to play any of the  
titles that were purchased, click Play Now.  
11 Press the button to go to the previous menu.  
Watching movies with Netflix®  
To use the Netflix® service, connect this player to your network, and configure the network settings if they are  
not yet finished. In order to use this service, you must set up or use an existing account.  
Launching Netflix® movie  
1
Press the HOME button on the remote control or select Portal in the setup screen to display the ePortal  
Home.  
Use the / /  
2
/
buttons to select Netflix icon, and then press OK to enter the Netflix® menu.  
Creating Netflix® account  
1
2
If you are not a Netflix® member: Select no.  
Read the instructions displayed on the TV screen, and visit http://www.netflix.com/toshiba from your  
PC.  
3
4
5
Sign up to create your account, then select “I’m now a member”.  
If you are a Netflix® member, select yes.  
Enter a valid email address and password.  
Preparing Instant Queue  
To play streaming video via Netflix® service, Netflix® player needs to be activated. Read the instructions  
displayed on the TV screen. Sign in to your Netflix® account with your email address and password. Now you  
can view Netflix® streaming video. After having activated Netflix® player and prepared Instant Queue, movies  
and TV episodes in your Instant Queue appear on the TV screen. Select your desired one using the remote  
control of the player.  
Resolution of video streamed from Netflix® varies depending on communication speed or  
bitrate of each content, etc.  
 
Network functional description  
35  
Watching movies with YouTube®  
This service enables you to use the following services provided by YouTube®.  
1
Press the HOME button on the remote control or select Portal in the setup screen to display the ePortal  
Home.  
2
3
Use the / /  
/
buttons to select YouTube icon, and press OK.  
Now you can select the video content you wish to watch.  
Watching movies with VUDUTM  
To use the VUDUTM service, connect this player to your network, and configure the network settings if they are  
not yet finished. In order to use this service, you must set up or use an existing account.  
Creating a VUDU™ account on your player  
1
Press the HOME button on the remote control or select Portal in the setup screen to display the ePortal  
Home.  
2
3
4
Use the / /  
/
buttons to select Vudu HD Movies or Vudu Apps icon, and press OK.  
Follow the instructions to create an account; it will ask for an email address.  
Enter YOUR email address using the software keyboard on the screen. VUDU™ will then display a  
message on the TV “Sending you an email”.  
Creating a VUDU™ account on your PC  
1
2
VUDU™ will send you an email with a hyper-link; click on the link.  
After clicking on the link, the VUDU™ page appears on your PC’s browser then enter the e-mail and  
password for the account.  
VUDU™ will then display a message “Enabling your device to view movies. The email message on  
your TV screen will disappear when done”.  
3
On your TV, you can now navigate to a VUDU™ movie, and ‘buy’ or ‘rent’ it.  
Watching movies with Hulu Plus™  
To use the Hulu PlusTM service, connect this player to your network, and configure the network settings if they  
are not yet finished. In order to use this service, you must set up or use an existing account.  
Log in to Hulu PlusTM with your account  
1
Press the HOME button on the remote control or select Portal in the setup screen to display the ePortal  
Home.  
2
Use the / /  
A message is displayed “Are you already a Hulu Plus subscriber?” on the screen.  
Use the button to select Yes, and then press the OK button to confirm.  
Log in to Hulu Plus and enter your email address and password using the virtual keyboard, then use the  
/ / buttons to move the cursor to Login and press the OK button to confirm.  
/
buttons to select Hulu Plus icon, and press OK.  
3
4
/
/
Creating a new Hulu Plus account on your PC  
Go to www.hulu.com/activate and enter your activation code to create a new account.  
Listening to music with Pandora®  
To use the Pandora® service, connect this player to your network, and configure the network settings if they  
are not yet finished. In order to use this service, you must set up or use an existing account.  
Using an existing Pandora® account  
1
Press the HOME button on the remote control or select Portal in the setup screen to display the ePortal  
Home.  
2
3
4
Use the / /  
/
buttons to select Pandora icon, and press OK.  
Select I have a Pandora account from the option list.  
Sign in with your account.  
 
Network functional description  
36  
Creating a new account on the SymbioTM Media Box and Blu-rayTM Player  
1
Press the HOME button on the remote control or select Portal in the setup screen to display the ePortal  
Home.  
2
3
Use the / /  
Select I am new to Pandora from the option list.  
/
buttons to select Pandora icon, and press OK.  
You will be given an activation code  
4
Use this activation code to generate a new account and link it to the player using a PC.  
Creating a new Pandora® account on your PC  
Visit http://www.pandora.com/ to create a new account.  
Browsing photos with Picasa™  
To use the PicasaTM service, connect this player to your network, and configure the network settings if they  
are not yet finished. In order to use this service, you must set up or use an existing account.  
Signing in with your account  
To display photos in your web album on the screen, you need to sign in with your Picasa™ account.  
1
Press the HOME button on the remote control or select Portal in the setup screen to display the ePortal  
Home.  
2
3
Use the / /  
/
buttons to select Picasa icon, and press OK.  
Enter your user name using the virtual keyboard, and press the OK button while [OK] is selected on the  
screen.  
4
Enter the password using the virtual keyboard, and press the OK button while [OK] is selected on the  
screen.  
Your web album is displayed on the screen.  
Creating a new Picasa™ account on your PC  
 
Troubleshooting  
37  
Troubleshooting  
If you experience any of the following difficulties while using this unit, check the list below before consulting  
your nearest TOSHIBA dealer.  
Problem:  
Solution:  
Connect the product to the power outlet.  
Point the remote control at the product.  
Insert the batteries correctly.  
No reaction to the remote control.  
Insert new batteries in the remote control.  
No video signal on the display device.  
Turn on the TV.  
Set the TV to the correct external input.  
Select the correct video resolution.  
Set TV System of TV correctly  
If the unit is connected to the unauthorized display device with an HDMITM  
cable, the audio/video signal may not be output.  
Ensure the amplifier/display devices setting match the Blu-ray Disc™  
player.  
Incorrect or no audio / video signal  
on the amplifier/display device via  
HDMITM cable.  
No high-definition video signal on  
the TV.  
Does the disc contain high-definition video? High-definition video is not  
available when the disc does not contain it.  
Does the TV support high-definition video? High-definition video is not  
available when the TV does not support it.  
No audio signal from the loudspeakers  
of the audio system.  
Turn on the audio system.  
Set the audio system to the correct external input.  
Increase the volume level of the audio system.  
Make sure that the Blu-ray Disc™ player supports the disc.  
Make sure that the Blu-ray Disc™ player supports the region code of the  
DVD or Blu-ray Disc™.  
Cannot play back a disc.  
Clean the disc.  
Cannot connect to the network.  
Check that the LAN cable connection is properly made.  
Check that the broadband router and/or modem is correctly connected.  
Check the Network Connection Setting.  
 
 
Glossary  
38  
Glossary  
Aspect ratio  
Aspect ratio refers to the length to height ratio of TV screens. The ratio of a standard TV is 4:3, while the ratio  
of a high definition or wide TV is 16:9. The letterbox allows you to enjoy a picture with a wider perspective  
on a standard 4:3 screen.  
AVCHD™  
AVCHD™ is a new format for high definition video camcorders which can record and play high-resolution  
HD images.  
AVI  
Audio Video Interleave, known by its acronym AVI, is a multimedia container format. AVI files can contain both  
audio and video data in a file container that allows synchronous audio-with-video playback.  
BD-Java™  
With some Blu-ray Disc™ which support Java™ applications, you can enjoy the interactive functions such  
as games or interactive menus.  
BD-Live™  
BD-Live™ is a BD-video (BD-ROM version 2 Profile 2.0/Profile 1.1) which contains new functions (e.g.  
Internet connection), in addition to the function.  
Blu-ray DiscTM  
Blu-ray DiscTM is a next generation optical video disc capable of storing five times more data than a  
conventional DVD. The large capacity makes it possible to benefit from the features such as high-definition  
videos, multichannel surround sound, interactive menus and so on.  
Chapter  
Just as a book is split up into several chapters, a title on a Blu-ray Disc™-video or DVD-video is usually  
divided into chapters.  
Digital Audio  
DigitalAudio is a sound signal that has been converted into numerical values. Digital sound can be transmitted  
through multiple channels. Analogue sound can only be transmitted through two channels.  
Dolby® Digital  
The system to compress digital sound developed by Dolby Laboratories. It offers you sound of stereo (2ch)  
or multichannel audio.  
Dolby® Digital Plus  
Dolby Digital Plus is the next generation digital audio compression technology developed as an extension to  
Dolby Digital. Blu-ray Disc™ supports 7.1 multi-channel surround sound output.  
Dolby® TrueHD  
Dolby TrueHD is a lossless coding technology developed for next generation optical discs. Blu-ray DiscTM  
supports 7.1 multi-channel surround sound output.  
DTS®  
DTS® is a multi-channel surround sound system. By connecting to DTS® decoder, you can enjoy movie  
dynamic and realistic sound like movie theater. DTS® surround sound technologies were developed by DTS®,  
Inc.  
DTS-HD®  
DTS-HD® is a lossless coding technology developed as an extension of the original DTS® Coherent Acoustics  
format. Blu-ray Disc™ supports 7.1 multi-channel surround sound output.  
DTS-HD Master AudioTM  
A disc encoded with DTS-HD Master Audio delivers ALL of the information from the original master recording  
— bit-for-bit, it’s identical to what the sound engineers laid down. Audio doesn’t get any better than this.  
HDCP  
High-bandwidth Digital Content Protection. This is a specification that provides a secure transmission of  
digital contents between different devices (to prevent unauthorized copyright.)  
 
Glossary  
39  
HDMITM  
High-Definition Multimedia Interface (HDMI) is a high-speed digital interface that can transmit uncompressed  
high definition video and digital multichannel audio. It delivers high quality picture and sound quality. HDMI is  
fully backward compatible with DVI. As required by the HDMI standard, connecting to HDMI or DVI products  
without HDCP (High bandwidth Digital Content Protection) will result in no Video or Audio output.  
IP Address  
A set of numbers which are assigned to devices participating in a computer network.  
JPEG  
A very common digital still picture format. A still-picture data compression system proposed by the Joint  
Photographic Expert Group, which features small decrease in image quality in spite of its high compression  
ratio. Files are recognized by their file extension ‘.jpg’ or ‘.jpeg’.  
LAN (Local Area Network)  
A group of linked devices in a company, school or home. Indicates the boundaries of a particular network.  
Local storage  
This storage area is used as destination for storing additional contents from BD-Live™ enabled Blu-ray  
Disc™-video.  
MP3  
A file format with a sound data compression system. MP3 is the abbreviation of Motion Picture Experts Group  
1 (or MPEG-1) Audio Layer 3. With the MP3 format, one CD-R or CD-RW can contain about 10 times more  
data than a regular CD.  
PCM  
Pulse Code Modulation. A digital audio encoding system.  
Region code  
A system that allows discs to be played only in the region designated. This unit only plays discs that have  
compatible region codes. You can find the region code of your unit on the product label. Some discs are  
compatible with more than one region (or ALL regions).  
Sampling Frequency  
The rate which sound is measured by a specified interval to turn into digital audio data. The numbers of  
sampling in one second defines as sampling frequency. The higher the rate, the better the sound quality.  
Title  
A collection of chapters on Blu-ray Disc™-video or DVD-video.  
Track  
Audio CD use tracks to divide up the content of a disc. The Blu-ray Disc™-video or DVD-video equivalent is  
called a chapter. See also “Chapter”.  
Wi-Fi®  
Wi-Fi or Wifi, is a mechanism for wirelessly connecting electronic devices.  
 
Specifications  
40  
Specifications  
General:  
Signal system  
NTSC  
Power requirements  
Power consumption  
120V AC, 60Hz  
12W  
Dimensions  
290 × 36 × 180(mm)  
(width x height x depth)  
Weight  
0.85 kg  
Operating temperature  
41°F (5°C) to 95°F (35°C)  
Operating humidity  
Less than 80% (no condensation)  
HDMITM output  
HDMITM jack x 1  
Video: 480i, 480p, 720p 1080i, 1080p, 1080p/24F / Audio  
Audio output (Coaxial digital)  
0.5Vp-p (75Ω)  
RCA jack x 1  
USB terminal x 1  
LAN terminal  
5V  
500mA  
100BASE-T  
Product specifications, configurations, prices, system/component/options availability are all  
subject to change without notice.  
Disclaimer  
1080p capable display required for viewing in 1080p. Viewing HD content and up-converting DVD content  
may require an HDCP capable input on your display device. While up-converting DVD video content may  
result in a picture that appears to be near HD quality, results may vary depending on content, display and  
settings. Feature performance may vary and may also require an always-on broadband Internet connection.  
Firmware update and additional bandwidth may be required. BD-Live™ requires connection of a USB device  
of at least 1 GB (sold separately) to USB port. Performance of interactive features may vary due to disc  
design or content, and may also require an always-on broadband Internet connection. Firmware update  
may be required for some interactive features. Some features may require additional bandwidth. Third party  
Internet services are not provided by Toshiba, may change or be discontinued at any time and may be subject  
to third party restrictions. Toshiba makes no representations or warranties about these services, which  
may require the creation of a user account through a computer with Internet access. Third party Internet  
service users may incur one-time and/or recurring charges. For Dolby® TrueHD and DTS-HD® Master Audio  
| Essential™ playback, content encoded in Dolby® TrueHD and DTS-HD® Master Audio | Essential™ format  
required. Viewing 1080p/24 fps output requires 1080p/24 fps encoded content and an HD display capable  
of accepting a 1080p/24Hz signal. Supported file types: JPEG, MP3, WMA, and AVCHD. Some recordable  
media, cards or files may not be supported. Product specifications, information and availability are all subject  
to change without notice.  
 
License Information  
41  
License Information  
END USER LICENSE AGREEMENT  
This End User License Agreement (“EULA”) is  
a
legal agreement between you and Toshiba  
Corporation(“Toshiba”) with regard to the copyrighted Software provided with this EULA. Use of any software  
and related documentation (“Software”) provided with a SymbioTM Media Box and Blu-ray Disc™ player, or  
made available by downloading or otherwise to you by Toshiba in whatever form or media, will constitute  
your acceptance of these terms, unless separate terms are provided by the software supplier or Toshiba in  
the documentation accompanying the SymbioTM Media Box and Blu-ray Disc™ player or otherwise, in which  
case certain additional or different terms may apply. If you do not agree with the terms of this EULA, do not  
use, download, install or copy the Software. If you wish to return a complete SymbioTM Media Box and Blu-ray  
Disc™ player system (hardware and software), contact the retailer where you purchased the SymbioTM Media  
Box and Blu-ray Disc™ player, and comply with the retailer’s standard return policies and procedures.  
Article 1 Definition  
The Software means all programs contained in the SymbioTM Media Box and Blu-ray Disc™ player. The  
copyright of the Software belongs to Toshiba and/or its suppliers, including BSQUARE Corporation and/or  
its suppliers. The Software is protected by copyright laws, Universal Copyright Convention, and other laws  
and conventions related to intellectual property rights. The content of the Software and manual is subject to  
change by Toshiba without notice.  
Article 2 License Grant and Use Conditions  
Toshiba grants to you a personal, non-transferable and non-exclusive right to use the copy of the Software  
in accordance with this EULA. You may permanently transfer all of your rights under this EULA, provided  
you transfer complete SymbioTM Media Box and Blu-ray Disc™ player together with all of the Software, you  
retain no copies, and the recipient agrees to the terms of this EULA. If the Software is an upgrade version,  
any transfer must include all prior versions of the Software. For maintenance purposes, you may update the  
version of the Software only for the SymbioTM Media Box and Blu-ray Disc™ player that is owned by you.  
Article 3 Prohibited Uses  
Unless otherwise expressly provided in this EULA or the product manual accompanying the SymbioTM Media  
Box and Blu-ray Disc™ player:  
3.1. You may not copy the Software, in whole or in part, without express written permission by Toshiba and/  
or its suppliers.  
3.2. You may not assign, resell, distribute or sublicense the Software or a copy of the Software.  
3.3. You may not create, assign, resell, or sublicense secondary works of the Software without permission.  
3.4. You may not modify, analyze, reverse engineer, decompile or disassemble any part of the Software.  
3.5. You may not combine or incorporate the Software with or into any other application.  
3.6. You may not print the Software.  
Article 4 Disclaimer  
Third Party Materials  
This Service may enable access to Toshiba’s and third party services and web sites, the Toshiba website  
within the Toshiba community and any other features, content, or services offered from time to time by  
Toshiba in connection with its website or this Application (collectively and individually, “ Third Party  
Services”). You understand that by using any of the Third Party Services, You may encounter content that  
may be deemed offensive, indecent, or objectionable, which content may or may not be identified as having  
explicit language, and that the results of any search or entering of a particular URL may automatically and  
unintentionally generate links or references to objectionable material. Nevertheless, You agree to use the  
Third Party Services at Your sole risk and that Toshiba shall not have any liability to You for content that may  
be found to be offensive, indecent, or objectionable. Certain Services may display, include or make available  
content, data, information, applications or materials from third parties (“Third Party Materials”) or provide  
links to certain third party web sites. By using the Services, You acknowledge and agree that Toshiba is not  
responsible for examining or evaluating the content, accuracy, completeness, timeliness, validity, copyright  
compliance, legality, decency, quality or any other aspect of such Third Party Materials or web sites. Toshiba  
does not warrant or endorse and does not assume and will not have any liability or responsibility to You or  
any other person for any third-party Services, Third Party Materials or web sites, or for any other materials,  
products, or services of third parties. Third Party Materials and links to other web sites are provided solely  
 
License Information  
42  
as a convenience to You. In addition, third party Services and Third Party Materials that may be accessed  
from, displayed on or linked to from Your device are not available in all languages or in all countries. Toshiba  
makes no representation that such Services and Third Party Materials are appropriate or available for use in  
any particular location. To the extent You choose to access such Services or Third Party Materials, You do so  
at Your own initiative and are responsible for compliance with any applicable laws, including but not limited  
to applicable local laws. Toshiba, and its licensors, reserve the right to change, suspend, remove, or disable  
access to any Services at any time without notice. In no event will Toshiba be liable for the removal of or  
disabling of access to any such Services. Toshiba may also impose limits on the use of or access to certain  
Services, in any case and without notice or liability.  
Article 5 Disclaimer  
5.1. THE HARDWARE PRODUCT LIMITED WARRANTY IS SET FORTH IN THE DOCUMENTATION  
ACCOMPANYING THE HARDWARE PRODUCT.  
5.2. THE SOFTWARE IS PROVIDED “AS-IS” AND “ASAVAILABLE,” WITHOUT WARRANTIES OF ANY  
KIND. ALL WARRANTIES AND CONDITIONS, EXPRESS OR IMPLIED, CONTRACTUAL OR STATUTORY,  
INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS  
FOR A PARTICULAR PURPOSE, TITLE OR NON-INFRINGEMENT ARE HEREBY WAIVED BY YOU AND  
DISCLAIMED BY TOSHIBA.THIS EULA REPRESENTS THE SOLE AND EXCLUSIVE OBLIGATION OF  
TOSHIBA AND ITS SUPPLIERS WITH RESPECT TO THE SOFTWARE.  
Article 6 Limitation of Liability  
TO THE MAXIMUM EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT SHALL TOSHIBA  
AND/OR ITS SUPPLIERS BE LIABLE FOR PERSONAL INJURY, OR ANY INCIDENTAL, SPECIAL,  
INDIRECT, PUNITIVE OR CONSEQUENTIAL DAMAGES WHATSOEVER, INCLUDING, WITHOUT  
LIMITATION, DAMAGES FOR LOSS OF PROFITS, LOSS OF DATA, BUSINESS INTERRUPTION, OR  
ANY OTHER COMMERNCIAL DAMAGES OR LOSSES, ARISING OUT OF OR RELATED TO YOUR USE  
OR INABILITY TO USE THE SOFTWARE, HOWEVER CAUSED, REGARDLESS OF THE THEORY OF  
LIABILITY (CONTRACT, TORT, OR OTHERWISE) AND EVEN IF TOSHIBAAND/OR ITS SUPPLIERS HAS  
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME JURISDICTIONS DO NOT ALLOW  
THE LIMITATION OF LIABILITY FOR PERSONAL INJURY, OR FOR INCIDENTAL OR CONSEQUENTIAL  
DAMAGES; THEREFORE, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU UNDER SUCH  
CIRCUMSTANCES. THE AGGREGATE LIABILITY OF TOSHIBA AND ITS SUPPLIERS IN CONNECTION  
WITH THE SOFTWARE, REGARDLESS OF THE FORM OF ANY LEGAL ACTION OR PROCEEDING,  
SHALL BE LIMITED TO DIRECT DAMAGES NOT TO EXCEED THE AMOUNT PAID FOR THE TOSHIBA  
BLURAY PLAYER.  
Article 7 Export Control  
Any export, directly or indirectly, of the Software in contravention of the United States Export Administration  
Regulations, or any other applicable law, regulation, or order, is prohibited.  
Article 8 Termination of License  
In the event that you fail to comply with any of the terms and conditions contained herein, Toshiba shall have  
the right to immediately terminate this Agreement without any notification to you. Upon termination of this  
Agreement, you shall cease all use of the Software and destroy all copies, in whole and/or in part.  
Article 9 Governing Law  
This EULA is governed by the laws of Japan, without references to the conflict of laws principles. Any and all  
disputes arising hereunder shall be resolved exclusively by the Tokyo District Court, Japan, and you hereby  
consent to the exclusive jurisdiction of such court.  
Article 10 Severability  
If any provision of this EULA shall be held to be invalid, illegal or unenforceable, the validity, legality and  
enforceability of the remaining provisions hereof shall not in any way be affected or impaired.  
(C) 2001-2010 Toshiba Corporation  
The Software contains Macromedia® [Flash®] [Flash Lite™] technology of Adobe Systems Incorporated.  
Copyright© 1995-200[7] Adobe Systems Incorporated. All rights reserved. Macromedia, Flash, Macromedia  
Flash, [and Macromedia Flash Lite] are trademarks or registered trademarks of Adobe Systems Incorporated  
in the United States and other countries.  
 
License Information  
43  
License information on the software used in the SymbioTM Media Box and Blu-ray Disc™ player. This  
document is statement purpose only. Not concerned with operation of this product.  
The software pre-installed in the SymbioTM Media Box and Blu-ray Disc™ player consists of multiple,  
independent software components. Each software component is copyrighted by TOSHIBA or a third party.  
The SymbioTM Media Box and Blu-ray Disc™ player uses software components that are distributed as freeware  
under a third-party end-user license agreement or copyright notice (hereinafter referred to as a “EULA”).  
Some EULAs require that the source code of the applicable component be disclosed as the condition for  
distributing the software component in executable format. You can check the software components subject  
to such EULA requirements on the following phone number:  
Phone number: 888-592-0944  
TOSHIBA provides a limited warranty for the SymbioTM Media Box and Blu-ray Disc™ player you have  
purchased under conditions set forth by TOSHIBA.  
However, some of the software components distributed under an EULA are made available for use by the  
user on the assumption that they are not copyrighted or warranted by TOSHIBA or any third party. These  
software components are licensed to the user free of charge and therefore not covered by any warranty  
within the scope of the applicable laws. These software components are not subject to any copyrights or  
other third-party rights and are provided in “as is” condition without any warranty, whether express or implied.  
“Warranty” here includes, but not limited to, an implied warranty for marketability or fitness for specific uses.  
All risks associated with the quality or performance of these software components are assumed by the user.  
TOSHIBA shall not be liable whatsoever for any cost of repair or correction or other incidental expense  
incurred in connection with a defect found in any of these software components. Unless specified under the  
applicable laws or in a written agreement, a party who changes or redistributes the software with consent  
from the copyright holders or based on the aforementioned licenses shall not be held liable whatsoever for  
any loss arising from the use of or inability to use such software components. The same applies even when  
the copyright holders or relevant third parties have been informed of the possibility of such loss. “Loss”  
here includes normal, special, incidental and indirect loss (including, but not limited to, the loss of data or  
its accuracy; loss incurred by the user or any third party; and interface incompatibility with other software).  
Please read each EULA for details on the use conditions and items that must be observed regarding these  
software components.  
The table below lists the software components preinstalled in the SymbioTM Media Box and Blu-ray Disc™  
player, which are subject to EULAs. The user should read the applicable EULAs carefully before using  
these software components. The EULAs are exhibited in their original text (English) as exactly written by the  
respective parties other than TOSHIBA.  
For the Open-Source Software Included in the SymbioTM Media Box and Blu-ray Disc™ player, type http://  
oss.bd.toshiba.com/version2 in your browser and click on the corresponding Open-Source Software License  
link.  
The Open-Source Software included in the SymbioTM Media Box and Blu-ray Disc™ player is described in  
your browser and click on the corresponding Open-Source Software License link provided. Additionally, the  
licenses can be viewed by typing in the URL addresses listed in the License column.  
OSS name  
OSS  
OSS project URL  
OSS license  
version  
2.6.35  
4.5.1  
GPLv2  
Linux kernel  
gcc libgcc  
GPLv3.txt and gcc-exception.txt (GPLv3  
with GCC Runtime Library Exception)  
4.5.1  
GPLv3.txt and gcc-exception.txt (GPLv3  
with GCC Runtime Library Exception)  
gcc libstdc++  
glibc  
2.12.2  
LGPLv2.1  
 
License Information  
44  
OSS name  
OSS  
OSS project URL  
OSS license  
version  
SquashFS  
4.1  
GPLv2  
iputils  
s20101006  
GPLv2  
GPLv2  
udhcpc  
0.9.8cvs2005  
0303-3  
downloads/0.9.8cvs20050303-3/  
net-tools  
sysvinit  
1.60  
view/6.3/basicnet/net-tools.html  
GPLv2  
2.88dsf  
sysvinit  
GPLv2  
GPLv2  
module-init-tools 3.12  
index.php/Main_Page  
util-linux-ng  
2.18  
util-linux-ng/  
GPLv2  
procps (ps, top)  
psmisc  
3.2.8  
22.13  
6.9  
GPLv2  
GPLv2  
GPLv2  
GPLv2  
GPLv2  
coreutils  
gawk  
3.1.5  
2.5.1a  
4.2.31  
grep  
findutils  
bash  
tar  
3.2.48  
1.17  
GPLv2  
GPLv2  
GPLv2  
GPLv2  
sed  
gzip  
4.1.5  
1.3.12  
inetutils  
1.4.2  
5.7  
GPLv2  
ncurses  
ncurses.txt  
GPLv2  
gdb (gdbserver)  
Das U-Boot  
6.6  
2009.08  
WebHome  
GPLv2  
International  
Components for  
Unicode  
3.2.0  
html  
ICULicense.txt  
OpenSSL  
dibbler  
FreeType  
Expat  
0.9.8x  
0.8.0  
2.3.9  
2.0.1  
openssl.txt  
GPLv2  
FreeType.txt  
expat.txt  
libcurl  
libjpeg  
7.21.7  
jpeg-7  
libcurl.txt  
libjpeg-7.txt  
c-ares  
1.7.4  
c-arse.txt  
 
License Information  
45  
OSS name  
mtd-utils  
libmtp  
OSS  
version  
OSS project URL  
OSS license  
1.2.0  
index.html  
GPLv2  
0.3.6  
LGPLv2.1  
libusb  
1.0.2  
0.1.2  
LGPLv2.1  
LGPLv2.1  
libusb-compat  
LibusbCompat0.1  
wpa_supplicant  
libnl  
0.8.x  
WPASupplicant.txt  
GPLv2  
1.0-pre7  
view/svn/basicnet/libnl.html  
Wireless Tools  
29  
Tourrilhes/Linux/Tools.html  
DirectFB  
Fusion  
1.2.7  
8.2.0  
1.4.0  
1.2.35  
LGPLv2.1  
GPLv2  
SaWMan  
libpng  
LGPLv2.1  
html  
libxml2  
tinyxml  
2.7.6  
2.5.3  
libxml.txt (MIT License)  
tinyxml.txt  
David M. Gay’s  
dtoa and strtod  
DMG’s dtoa and strtod.txt  
Bison generated  
parser  
2.3  
bison_parser.txt  
dmalloc.txt  
Doug Lea’s  
malloc  
malloc.html  
EMX sprintf and  
scanf  
EMX_sprintf_sscanf.txt  
JSON_Parser.txt  
JSON_Parser  
1.0  
xz  
5.0.3  
2.8  
cpio  
Qt  
4.7.0  
1.06.38  
LGPLv2.1  
xmlrpc-c  
xmlrpc-c.txt  
gSOAP  
2.7.12  
soap.html  
gSOAP.txt (gSOAP Public License  
1.3a)  
SQLite  
3.6.22  
4.3.0  
5.1.3  
sqlite.txt (public domain)  
BSD  
mcr-tcpdump  
Lua interpreter  
lua.txt (MIT License)  
 
License Information  
46  
OSS name  
OSS  
OSS project URL  
OSS license  
version  
zziplib  
0.13.58  
52.31.0  
49.15.0  
52.20.0  
zziplib.txt  
LGPLv2  
LGPLv2  
LGPLv2  
libavformat  
libavutil  
libavcodec  
zlib  
1.2.3  
zlib.txt  
lighttpd  
nmbd  
ntp  
1.4.29  
BSD License  
GPLv2  
2.2.12  
4.2.6  
GPLv2  
live555  
(for BDX3400KU  
ONLY)  
2011.06.12  
LGPL V2  
©2013 Toshiba America Information Systems, Inc.  
• GMA300021010 • 4/13  
 

TC electronic SDN BHD Guitar NDY 1 User Manual
Technika CRT Television LCD26 209X User Manual
The Swan Corporation Indoor Furnishings BS 1515 User Manual
Thule Automobile Accessories 077 User Manual
Toro Lawn Mower 14AP80RP744 User Manual
Toshiba VCR W 515 User Manual
TRENDnet Router 54Mbs 80211g ADSL Modem Router User Manual
Uniden Marine Radio UM380BK User Manual
Vivitar Camera Accessories MagnaCam 1025x1 Digital Camera Binocular User Manual
Walker Snow Blower SB36 User Manual